EPOXYCEMENT
EPOXYCEMENT is a three-component epoxy mortar (resin, hardener, aggregates).
If the thickness is less than 10 mm, the use of the primer POXYFIRST is strongly recommended.
Main uses:
- Repairing cement or tiled floors,
- Filling large cavities and cracks,
- Creating mini screeds on degraded cement floors, forming slopes or leveling uneven surfaces.
- Sealing balcony ramps or metal parts in cement.
Available colours:
sand
Packaging:
Pre-dosed components to mix before use:
- 12.5kg kit: 0.890kg of component A + 0.445kg of component B + 11.170kg of component C (Aggregates)
- 25kg kit: 1.780kg of component A + 0.890kg of component B + 22.340kg of component C (Aggregates)
Key benefits:
- Continuous coating, without shrinkage.
- Resistance to wear, abrasion, acids, bases, oils, as well as diesel fuels.
Consumption:
- For 5 mm thickness: 11 kg/m²
- For 10 mm thickness: 22 kg/m²
Technical characteristics:
| Mixing ratio by weight: | Comp. A: 7.13 Comp. B: 3.57 Comp. C: 89.30 |
| Theoretical density of the mixture: | 2.2 |
| Dry extract: | 99.75 % |
| Adhesion on concrete: | > 65 kg/cm² |
| Compressive strength: | 740 kg/cm² |
| Polymerisation after 24 H: | 55 % |
| Polymerisation after 6 days: | 99 % |
| Pot life on a 1500g sample: | Approx. 50 min |
| Open time spread: | 30 min |
Mix preparation and application:
- Ensure that surfaces are clean and dry. Free from dust, grease, moisture, oil...
- The use of our primer POXYFIRST is strongly recommended.
- Mix the two components (they are delivered pre-dosed) for 2.5 to 3 minutes at a speed of 400 rpm with an electric mixer.
- Pour the mixture into a suitable container, then add the aggregates (comp. C). Homogenise everything with a powerful mixer. (For quantities greater than 50 kg, use a concrete mixer or a special mixer).
- Spread the mixture on the floor using a ruler, then smooth with a stainless steel or steel trowel.
Application and storage conditions:
- Ambient temperature: 12°C to 35°C.
- Substrate temperature: 12°C to 25°C.
- Humidity level: must be less than or equal to 5 % for concrete.
- Humidity: max. 75 %.
- Storage: Keep in an intact package at an ambient temperature between 15°C and 25°C.
- Shelf life: 12 months.
For more information, please refer to the technical data sheet. 3-component epoxy mortar (resin, hardener and aggregates) applied with or without primer. Very good resistance to wear, abrasion and acids, without shrinkage. Main uses: repairing cement or tiled floors, filling large cavities and cracks, etc. Consumption: for 5 mm thickness: 11kg/m². for 10 mm thickness: 22 kg/m². Substrate preparation: Substrates must be dry, free of dust, grease, oil, moisture, curing agent, brittle or loose parts and must not be subject to rising damp by capillary action. Stripping is done by mechanical action (sanding, planing, shot-peening, diamond grinding). The use of our solvent-free epoxy primer PoxyFirst is strongly recommended for epoxy mortar thicknesses of less than 10 mm. Mix preparation: The components (Comp A resin + Comp B hardener + Comp C aggregates) are delivered pre-dosed. Components A + B should be mixed for 2.5 to 3 minutes at a speed of 400 rpm with an electric mixer fitted with a helical paddle (right-hand pitch) with a diameter approximately 2.5 times smaller than the diameter of the seal. Pour the hardener resin mixture into a suitable container (50 litre dustbin) and then add the aggregates (Comp.C). Proceed to mix the whole with a stirrer of sufficient power until the aggregates are completely coated. For quantities greater than 50 kg, use a concrete mixer or a special mixer. Application: spread the mixture on the floor with a ruler, smooth with a stainless steel or steel float. In case of a thickness of less than 10 mm a PoxyFirst precoat is necessary at a rate of 0.250 Kg/m².
